Roller shutter motor test - comparisons. Com 2024

Do you also drive your shutters with muscle power? You may think that can not change so easily and above all without structural effort. But far from it. We show you in our Belt drive guide from Test-Vergleiche.com How to retrofit an electric belt drive with little effort.

In a nutshell, what does a motorized roller shutter bring?

• Force is eliminated
• good investment for the elderly
• Improving the climate if the roller shutter has a sun sensor
• Control via a timer is possible
• travel safely with the random program
• partial control from the sofa by remote control
• partially fully automatic opening and closing thanks to Astro program

The difference between tubular motor and Gurtwickler

So much is said in advance, both variants can be retrofitted, but with different effort. The shutter motor, which is inserted into the shaft of the shutter, requires a power connection on site. So in the immediate vicinity of the wave. Of the electric belt winder however, it is only exchanged for the hand-operated Gurtwickler. Because it has a power cord, it only needs one outlet nearby. The installation of both variants is relatively simple, but is more complicated if there is no power connection in the vicinity of the shutter.

The tubular motor drive

The Professional roller shutter drive is undoubtedly the optimal variant to operate a blind without muscle power. This type of drive is ideal for large and heavy roller shutters. The connection disappears completely in the wall. A belt is no longer needed and only possibly a switch (blind switch) disturbs the appearance. This can however be attached at any point. With a little manual skill is one Roller shutter drive low install. The installation is done in a few steps.

• First, the access door is opened. This is usually the lower lid of the shutter box.
• Now the roller shutter has to be lowered all the way down and the belt has to be unhooked.
• In the removed shaft now the electric roller shutter motor must be inserted.
• Hook the tank back in and close the access panel again.
• Remove the old belt drive. Finished.

Now you have an electrically powered motor in your roller shutter, but you need an 230 Volt power connector and a control unit. Here, the electrician must lend a hand and lead a power supply line into the inspection box of the shutter. This usually does not work without structural changes. Unless, of course, you can settle for an electrical installation duct laid on plaster.

The easiest way to operate the blinds is to install a shutter switch near the window. This allows you to manually open and close your shutters. But you can also combine several shutters with a single control unit or completely automate the operation by controlling your shutters on a timer, temperature, wind and sun sensors or a fully automatic Astro program. Even an operation via radio remote control is possible.

The roller shutter drive range is available for all types of blinds, such as the top-mounted roller shutters, the front blinds as well as for the built-in shutters. Pay attention to the weight or the surface of the shutter. Plastic light roller blinds require about 5 kg tensile force per square meter, aluminum 5,5 kg and 11 kg for old wood versions. The tractive power of the engine can be found in the manufacturer's instructions.

The electric belt winder

He is the Belt drive professional For the easiest re-installation of an electric drive for your blinds. Since it is fixed at the point where the manual hand winder sits, usually no major construction effort is required. The best belt drives are now designed to have the same mounting dimensions as the hand winder, replacing 1: 1 with the old winder. For the swiveling on-plaster Gurtwickler no measure must be observed. He is simply put in the place of the old.

The installation is very simple.

• Shut down shutters
• Release belt from old winder, remove hand winder
• attach new belt drive and insert belt. Finished.

Before you order a belt drive, you should familiarize yourself with the mounting dimensions. These play in a Auf-Putz version, however, does not matter. Unfortunately, only very few manufacturers specify this mounting dimensions, not even ours Roller shutter drive comparison winner of the Rademacher belt drive uP Comfort.

Naturally, too best belt drive Electricity. For the devices, the power supply is disconnected via a power cable with plug. It leads out of the bottom of the device and only needs to be connected to a suitable power outlet. There is no need for an electrician and that is why it is so Belt drive cheap to install.

While the tubular motor, a separate switching option is required, the shutter switch is integrated with the belt winder with the same. With it you can operate your blinds as well and drive up and down. With a cheap belt drive the shutter can only be moved up and down. Depending on the features of the model, the best shutter drives have to wind up the belt, the same comfort options as described in the tubular motor.

The automatic belt retractors have a special feature to consider. There are models that you can connect directly to an 230 Volt power outlet and those that run with 12 or 24 Volt and need a power supply to operate. This power supply is designed as a plug-in power supply and also comes into the socket. The downside is that the power supply takes away some space and the blind is operated via a connector strip, the place can quickly become tight.

Which Gurtwickler is the right one?

Similar to tubular motors, the belt winders also need to be classified in the tensile forces. The surface of the shutter can be measured relatively easily. As with tubular motors, the tensile load of 5 kg / m² must be expected for a plastic roller blind, 5,5 kg / m² for aluminum shutters and even 11 kg / m² for wooden shutters.

Example: Area 1,5 mx 2,5 mx 5 kg for plastic = 18,75 kg

Since the roller shutter creates friction when you open and close, you still recommend 10% for safety. This results in a weight of 20,6 kg.

About this Belt drive draw weight not just the Professional roller shutter motor Even with the cheap belt drive, the same premises apply to drive the roller shutter safely. For most manufacturers, the data on the tensile force are in the product data. Sometimes only the surface of the shutter is specified, which you can convert according to the above method.

Where can I buy a shutter motor?

Today you can easily get one Roller shutter drive or belt drive online to order online, In our Roller shutter motor Price comparison you can buy your desired article immediately afterwards. Our purchase recommendations and the roller shutter motor comparison winner chosen by us should make your choice a little easier and give you a good overview when comparing dealers.

The three best-known manufacturers of engines and spare parts are:

• Rademacher roller shutter drives
• SuperRollo belt drives
• Schellenberg roller shutters

When shopping on the Internet, you can also make some bargains. Belt drives Offers, Roller shutter motor sale Actions or reduced roller shutter drives are also often found in the net. Cheap does not have to be equally cheap, so they should rather do without cheap roller shutter drives. If the installation effort is limited, a reduced shutter drive is always better than a no-name product, which just survives the warranty period.

What does Stiftung Warentest say about roller shutter motors?

Unfortunately, neither belt drives nor roller shutter motors have been examined by Stiftung Warentest. However, the Foundation is already aware of the advantages of using a roller shutter. In a report from the 23.06.2016, the foundation points out that blinds are good for the living environment. They not only protect against the summer heat, they also keep the cold outside the house in winter. It also protects against burglars. Furthermore, Stiftung Warentest points out that the costs of installation can be subsidized by the state. While you are at a mobile air conditioning just pay, a sunscreen could still flush your money in the cash.

A word in its own right

If you think that the shutter actually writes with 3 x L, ie RoLLladen, we have to agree with you. After the spelling reform in the year 2006 the spelling was corrected. The old spelling is still present on the Internet and at the dealers, which is why we are beaten and have preferred the old spelling.

Conclusion: A roller shutter motor or an electric belt winder increase the comfort when operating your blinds. Both are easy to retrofit and can also be used for older models. A small investment that will pay off in the next summer or winter. Also, as a help for the elderly, a belt winder or a roller shutter motor radio is an ideal purchase.